+49 (0)7024 9403-20
To the library
To the libraryTo the library
Frequently asked questions
Our technical help line is often confronted with similar questions. Here you will find an overview of the most common questions asked:A ceramics surface has dull spots, which have the shape of drops. Presumably, mineral water,
sparkling wine or something like it was spilled. Is the tile damaged?
can this surface be refurbished?
In order to remove the dirt, the wax film must be partially dissolved. Dilute Lithofin WEXA up to 1:4 with water (test for the adequate degree of dilution in an inconspicuous area) and apply it to the surface. Allow the product to work for 10 to 15 minutes. Brush vigorously and rinse the surface with plenty of clear water. Allow the surface to dry completely. Applying Lithofin TC Classic Wax or Lithofin TC Ever-Sheen will achieve an elegant sheen on the surface.
Product residues were not removed in time and have dried on the surface. These dull areas can be removed with Lithofin WAX-OFF and a white nylon pad.
shiny. What went wrong?
Lithofin MN Colour Intensifier has probably been applied too generously. The stone could not absorb the quantity of product and the product residues formed puddles which dried on the surface. This surface film can be dissolved with Lithofin MN Colour Intensifier. Simply reapply the product and ensure an even distribution. After 5 to 10 minutes, remove all surface residues with a dry cloth. The colour intensifying effect and the impregnator’s effectiveness remain intact. Alternatively, you can remove the impregnator entirely with Lithofin WAX-OFF. Apply the product with a brush and allow it to work for 15 to 20 minutes scrubbing occasionally. The rinse the surface with plenty of clear water.
two or three days, the surface turned white. What should be done?
The impregnator has probably been applied to a still moist surface. Remove the protective treatment with Lithofin WAX-OFF. When the surface has completely dried, reapply the impregnator.
At first glance, natural stone surfaces look dense and robust. However, the stone contains pores and capillaries, which allow dirt to penetrate the surface.
A protective treatment like Lithofin MN Stain-Stop (or Lithofin STAINSTOP >W<) makes the surface resistant to oil, grease and water borne dirt. Dirt does no longer penetrate the stone and is therefore simple to remove. The protective treatment in combination with the right maintenance program will prevent staining.
porcelain tiles. What should I do?
Sometimes, the polished tiles are not thoroughly cleaned off when they leave the factory and there are still residues from the polishing process. These residues can be removed with acidic cleaners such as Lithofin KF Cement Residue Remover.
Wet the surface with water, then apply Lithofin MN Builder's Clean and allow it to work for about one hour. Add some water, brush, and then remove the product. Rinse thoroughly with clear water. In case of stubborn staining repeat this process. Note: Some granites are pre-treated with products that may not be resistant to an acidic cleaner. Please test the product’s suitability prior to use. Discolorations resulting from plants look similar to rust and can be removed with Lithofin MN Outdoor Cleaner.
Put some Lithofin WAX-OFF (undiluted) on the spot. Allow the product to work for 10 to 15 minutes, brushing occasionally. Then rinse the surface with plenty of clear water.
Lithofin KF Mildew-Away will bleach most colours. Spray the product on the marks and rinse with plenty of water (while rubbing with a sponge) when the marks have disappeared.
Apply Lithofin MN Power-Clean, chemically-mechanically remove lime scale residues using a white nylon pad in circular motions. Recommendation: Regularly treat the window sill with Lithofin MN Polish Cream. The chemical agents make the water pearl off and thus facilitate cleaning.
Apply Lithofin MN Outdoor Cleaner undiluted and allow it to work for about 10-30 minutes. Brush, remove the product and then rinse off with clear water.
to the heaviest use. How can I bring back a nice sheen on the surface?
First remove any dirt and care product residues with Lithofin MN Power-Clean. Afterwards wipe the surface with Lithofin MN Care-Sheen. (in case of hard wear: apply Lithofin MN Care-Seal diluted 1:4 with water). You may have to repeat this procedure in order to achieve a rich sheen. Use Lithofin MN Wash & Clean or Lithofin EASY-CARE for regular maintenance.
residues. What should I do?
Apparently, layer-building care products have left residues on the surfaces which are being redistributed with each wiping. Dilute Lithofin FZ Intensive Cleaner approx. 1:5 with water and apply it to the surface. Allow the product to work for 20 minutes, then brush and thoroughly rinse the surface with plenty of clear water. For regular maintenance, use Lithofin FZ Conditioning Cleaner (for Australia and New Zealand: Lithofin FZ Vitra-Clean).
achieve the same intense colour when the surface is dry?
Generously apply Lithofin MN Colour Intensifier to the clean and completely dried out surface. In addition to giving the surface a deep and rich colour, Lithofin MN Colour Intensifier also acts as a protective treatment against water and dirt. Note: Also suitable for all porous natural stones.
Brush the surface several times with hot water and a dash of Lithofin MN-Power-Clean Occasionally you may have to put a wet cloth on the area and allow the product to work for some time.
them from turning dark again?
Grease splashes and vapours penetrate into the porous grouting material and with time turn them dark and unsightly. Lithofin KF Grout Cleaner dissolves and removes these deposits. However, oil and grease turn into resin with time, and they become more and more difficult to remove as time goes by. The clean joints should then be treated with Lithofin KF Grout Protector. This protective treatment will prevent the penetration of oil and grease.
some parts even black. How can I clean these surfaces?
Cleaning the surface with Lithofin MN Outdoor Cleaner will restore the surface to its original condition. After one to two weeks, you should treat the surface with Lithofin ALGEX as a preventive measure. To ensure a clean surface in the future, you should spray it with Lithofin ALGEX once a year, preferably in spring.
Green deposits can be removed with Lithofin ALGEX. Simply dilute the product 1:10 with water and spray it onto the surface. This product also serves a preventive function. To ensure a clean surface, you should spray it with Lithofin ALLEX once a year, preferably in spring.
First you should thoroughly clean the surface with an intensive cleaner. If the slippery surface was due to layer forming care products, the problem should now be solved. If the surface is still to slippery, you can use Lithofin Anti-Slip to “roughen” up the surface. The product removes microscopically small silicate particles from the stone / tile, thereby giving it more grip. Lithofin Anti-Slip is available in a convenient Set which includes all the equipment you will need to treat 6m².
The grey film can be removed with Lithofin KF Cement Residue Remover. Depending on the type of terracotta and the stubbornness of the deposits, dilute the product 1:15 to 1:5 wit water. Then apply the solution, allow it to work briefly, brush and rinse off the surface with plenty of water.
Protecting the surface with Lithofin STAINSTOP >W< will prevent water, dirt, oil and grease from penetrating into the surface, thereby simplifying maintenance.
brown. What do I need to do?
It is best not to do anything. You probably used Lithofin ALGEX in too strong a concentration, which made the algae turn brown. You can either brush with some water or wait for the rain to solve the problem.